Tools / Q codes and RST reports

Q codes and RST reports

Every Q code you're likely to hear on the bands, with what it means as a question and as a statement. Type in the box to find one fast.

CodeAs a questionAs a statement
QRAWhat is the name of your station?The name of my station is…
QRBHow far are you from my station?The distance between our stations is…
QRGWhat's my exact frequency?Your exact frequency is…
QRHDoes my frequency vary?Your frequency varies.
QRIHow is the tone of my transmission?Your tone is good, variable or bad.
QRKHow readable are my signals?Your signals are readable 1 to 5.
QRLAre you busy? Is this frequency in use?I am busy, or this frequency is in use.
QRMAre you getting interference from other stations?I'm getting interference from other stations.
QRNAre you troubled by static or noise?I'm troubled by static or noise.
QROShall I increase power?Increase power. Also used to mean running high power.
QRPShall I decrease power?Decrease power. Also used to mean low-power operating, usually 5 W or less.
QRQShall I send faster?Send faster.
QRSShall I send more slowly?Send more slowly.
QRTShall I stop sending?I'm stopping, or closing down the station.
QRUHave you anything for me?I have nothing for you.
QRVAre you ready?I'm ready, or I'm active on this band.
QRXWhen will you call me again?Please wait, I'll call you again shortly.
QRZWho is calling me?You're being called by…
QSAWhat is my signal strength?Your signal strength is 1 to 5.
QSBAre my signals fading?Your signals are fading.
QSDIs my keying defective?Your keying is defective.
QSKCan you hear me between your signals?I can hear you between my signals. Full break-in on CW.
QSLCan you acknowledge receipt?I acknowledge receipt. Also a card or electronic confirmation of a contact.
QSOCan you communicate with…?I can communicate with… In amateur use, a contact.
QSPWill you relay a message to…?I'll relay a message to…
QST–A general call to all amateurs, used for bulletins.
QSXWill you listen on…?I'm listening on… Used when working split.
QSYShall I change frequency?Change frequency to…
QTCHow many messages have you to send?I have … messages for you.
QTHWhat is your location?My location is…
QTRWhat is the correct time?The correct time is… (in UTC)

RST signal reports

A report like 59 on voice or 599 on CW gives readability, strength and, for CW and digital, tone.

R: Readability

  • 1: Unreadable
  • 2: Barely readable, occasional words
  • 3: Readable with considerable difficulty
  • 4: Readable with practically no difficulty
  • 5: Perfectly readable

S: Signal strength

  • 1: Faint signals, barely perceptible
  • 2: Very weak
  • 3: Weak
  • 4: Fair
  • 5: Fairly good
  • 6: Good
  • 7: Moderately strong
  • 8: Strong
  • 9: Extremely strong

T: Tone (CW and digital only)

  • 1: Sixty-cycle AC or less, very rough
  • 2: Very rough AC, very harsh
  • 3: Rough AC tone, rectified but not filtered
  • 4: Rough note, some trace of filtering
  • 5: Filtered rectified AC, strongly ripple-modulated
  • 6: Filtered tone, definite trace of ripple
  • 7: Near pure tone, trace of ripple
  • 8: Near perfect tone, slight trace of modulation
  • 9: Perfect tone, no trace of ripple

Where Q codes come from

Q codes are three-letter abbreviations, all starting with Q, that began in the early 1900s so that ship and shore operators could exchange common messages in Morse code without sharing a language. The International Telecommunication Union still maintains them. Each code has two meanings: followed by a question mark it asks something, and on its own it answers or states it. QTH? means "what is your location?", and QTH London means "my location is London".

Radio amateurs use a small set of Q codes all the time on CW, and many have slipped into voice and everyday ham slang. A QSO is a contact, a QSL is a confirmation card, QRP means low power, and QRT means closing down.

How amateurs use them on voice

Strictly speaking Q codes are for Morse, but a few are so convenient that they're used on SSB and FM too. You'll hear "the QTH here is Manchester", "QRZ?" after a pile-up, "QSY to 145.500", and "QSB is heavy tonight". Keep it to the common ones. On voice, plain language is clearer for everyone, especially newer operators.

Giving a good signal report

Readability matters more than the S-meter. If you copy every word easily, the R is 5, even if the signal is weak. For S, use what you hear, or your meter if it's calibrated. Most give 5 and 9 by habit in contests, and that's accepted there, but an honest report is more useful in a normal contact.

Questions

What does QTH mean?

Your location. QTH? asks where the other station is, and QTH London means you're in London. Many amateurs give their Maidenhead locator as well.

What does QSL mean?

It means “I acknowledge receipt”. Amateurs also use it for the card or electronic confirmation, such as LoTW or eQSL, that proves a contact took place.

What does 73 mean?

73 isn't a Q code. It's from the old telegraph numeric codes and means “best regards”. 88 means “love and kisses”, and you'll mainly hear it between friends.

What does 599 mean?

It's an RST report: readability 5 (perfect), strength 9 (extremely strong) and tone 9 (perfect). On voice the tone is dropped, so it's just 59.